As an Amazon Associate I earn from qualifying purchases. Some links on this page may earn RealIRacing a commission at no extra cost to you. Gear I personally race on is called out as such; other picks are researched recommendations.

The iRacing baseline is a trap disguised as a gift. It's fast enough that you think you're done, but it's also generic enough that it leaves performance on the table, especially when the track temperature changes, your preferred brake pressure doesn't match the default, or your rig's geometry is different from whatever alien's setup they tuned it on. Treat baseline as a starting point, not a destination: a few targeted tweaks can recover whole tenths.

The key is knowing what to change first, in what order, and when to stop. Chaotic setup adjustments kill confidence and waste time. A systematic approach, testing one or two variables at a time on the same fuel load and tire age over multiple laps, is how you actually improve without spinning into the weeds.

Why Baseline Isn't Enough

iRacing's baseline setups are solid. They're built by fast drivers and tested across a range of conditions. But they're also compromises. A baseline has to work for a 70 kg driver and a 90 kg driver, on a rigid frame and a flexy cockpit, with fresh tires and worn tires. It's the broadest-spectrum setup that won't embarrass you.

The problem: baseline doesn't know your brake pressure preference, your throttle sensitivity, whether you trail-brake or lift-and-coast, or what fuel load you'll actually run. And it definitely doesn't account for your specific seating position and pedal angles, which change how braking force translates into stopping power on your setup.

The Three-Phase Approach

Phase 1: Brake and Throttle Mapping (Your Foundation)

Before you touch suspension, sort your pedal inputs. This is non-negotiable. Use the MOZA CRP2 load cell calibration to dial in a pressure curve that matches your actual braking style, then run baseline for 10 laps to see if brake balance feels forward or rearward. On a ~9 N·m MOZA R9, also log peak wheel torque to see if you're exceeding the wheelbase's comfortable output during hard braking.

Adjust brake bias in small increments, 0.5% at a time, until the car feels neutral through hard corners. Throttle mapping is less critical if you're smooth, but if you're aggressive on exit, test a couple of throttle sensitivity settings to see which gives you the best traction without spinning the rear.

Phase 2: Suspension Stiffness and Roll (The Biggest Movers)

This is where baseline often fails individual drivers. Baseline anti-roll bars are usually set for a comfortable middle ground. If you're light or heavy, or if your cockpit has a lot of frame flex, the car will either wallow or feel nervous mid-corner.

Start with front anti-roll bar stiffness. Go one notch stiffer, run 10 laps at a consistent pace (same fuel, same tire age), and log your best lap. Then one notch softer, 10 more laps. Most drivers find a sweet spot where the car is responsive without feeling twitchy. If your frame is stiff and you prefer direct input, a common starting point is 2-3 notches stiffer than baseline on GT3 cars.

Phase 3: Damping and Ride Height (The Refinements)

Once ARBs feel right, damping (bump and rebound) and ride height come next. These are finer adjustments. Ride height affects both aero and mechanical grip; going lower usually improves aero but can bottom out over kerbs. Damping affects how the car responds to weight transfer: stiffer bump damping (compression) resists the chassis diving under braking, while rebound damping controls how fast it recovers.

Try ride height 2-3 clicks lower than baseline and check for bottoming in your telemetry. Then increase bump damping by 1-2 clicks to reduce dive under heavy braking. Rebound follows similarly. These are small, deliberate tweaks, not wild swings.

Test Stint Length

Damping changes feel subtle over one lap but compound over a stint. Run 10–15 lap runs, not single laps, to feel the real effect.

How to Test Systematically

Chaos kills setup progress. Here's a systematic workflow, whether you use a MOZA R9 and CRP2 or other gear:

  1. Set fuel to the same amount every test session (for example 25% fuel, roughly 90 kg total weight)
  2. Run baseline for 10 laps to establish a baseline pace and tire temps
  3. Change ONE variable (e.g., front ARB +1 notch)
  4. Run 10 laps at the same fuel level; note best lap and average pace
  5. Compare to baseline lap. If faster, save the setup. If slower, revert and try the other direction
  6. Once you find a direction (stiffer or softer), continue incrementally
  7. When progress stalls (gains drop below 0.05s per change), move to the next variable
  8. At session end, run 15 laps on your new setup at full fuel load to verify it's stable over distance

Telemetry is your truth. Record brake pressure, throttle input, wheel speed, and suspension travel for every test. If your best lap is 0.1s faster but your brake pressure is erratic, you've found a setup that suits one lap, not a setup that suits you. Look for consistency first, speed second.

Common Baseline Tweaks That Work

These are a few common tweaks that often improve baseline, depending on your driving style and rig:

None of these are universal. They depend on knowing your rig, your inputs, and your preferences. Your baseline might need the opposite: soft ARBs if your frame is flexy, a forward brake bias if you're aggressive on the pedal, or a higher ride height if the track is rough.

When to Stop Tweaking

The biggest mistake is chasing 0.02s improvements for three hours. At some point, you are not improving the setup; you are just shuffling variables and losing consistency. Stop tweaking when two conditions are met:

After that, track time beats setup time. Strap in for a 30-lap race simulation and drive the car. You'll learn more about it and about your own limits than you will from five more setup iterations.

Driver Confidence > Setup Perfection

A setup you trust and understand beats a theoretical optimum by 0.1s every time. Settle on something you feel confident in.

Example Workflow: Ferrari 488 GT3 at Monza

This is an illustrative walk-through, not a logged session. Say baseline pace is 1:44.2. Run it for 10 laps; if it's solid but feels loose in Turn 1, a high-speed left hander, increase front ARB from baseline (24) to 26 (two notches stiffer). Turn 1 may feel planted, but Turn 8 (chicane exit) can now turn oversteery. Dial front ARB back to 25, increase rear to 23 (baseline is 22), and run 10 more laps. Best lap: 1:43.9. Next, add 0.5% brake bias forward, which can help mid-corner stability under trail braking. Best lap: 1:43.6. Then drop ride height one click to improve aero on the straights. Best lap: 1:43.4. All told, that is 0.8s gained over six small, deliberate tweaks. Then stop and race the car.

The gear in this guide
PickWhy it made the listTested?
MOZA R9 Direct Drive Wheelbase9 N·m direct drive, the base bolted to my rig right nowRaced on
MOZA CRP2 Load Cell Pedalsload-cell brake, managed in the same Pit House softwareResearched pick
Sim Racing Cockpit / Wheel Standa rigid mount matters more than the brand; flex kills FFB detail.Researched pick

As an Amazon Associate I earn from qualifying purchases. Some links are affiliate links; I may earn a commission at no cost to you.

From the RealiRacing shop

Before your next session, free up your rig. NWM PitStop is the clean-up and stream-priority script set we run before every session; our own product, not a third-party pick. See NWM PitStop →

Watch it, don't just read about it

I stream and upload iRacing races on my MOZA R9 rig: real laps, real force feedback, real mistakes. See the gear from this guide working before you spend a cent.

▶ Subscribe on YouTube

Skip the trial and error

The force-feedback, pedal and baseline settings I actually race, written up as setup packs for MOZA, iRacing, ACC and Le Mans Ultimate. The opening section of each pack is free to read.

See the setup packs →

Free FFB tuning checklist

The order I tune force feedback in, from rig to wheelbase software to iRacing, plus the clipping check. Enter your email and the checklist opens right here. No spam, unsubscribe anytime.

See the privacy notice.

FAQ

How do I know if I should go stiffer or softer on anti-roll bars?

If the car feels like it's rolling too much in corners and understeers before the apex, go stiffer. If it feels nervous or oversteery, go softer. Start by testing your primary complaint in one repeatable corner, not the whole track. Stiffer = faster turn-in but more oversteer risk; softer = more mid-corner grip but slower turn response.

Can I just download a setup from a setup shop instead of tweaking baseline?

(FAQ) Yes, but you'll learn less and adapt slower to track temperature changes. A setup shop tune is optimized for their test driver on their rig. Tweaking baseline teaches you how your specific car and rig behave, which lets you make smarter adjustments when conditions shift mid-event. Treat shops as a reference, not gospel.

Should I tune suspension before or after brake balance?

Brake balance first. If your brakes aren't balanced, you can't accurately feel how the chassis handles mid-corner, because your inputs are fighting each other. Get brake balance dialed in, then suspend stiffness, then damping.

How many laps do I need to test a setup change?

For feel: 5 laps. For confirmation: 10 laps. For confidence over distance: 15+ laps. Single-lap tests are noise; tires warm up, you find confidence, and one lap doesn't reflect real race behavior. Run short stints (10 laps) for quick feedback, then longer stints (15–20 laps) when you've narrowed the window.